cb2000 correct fitting

Collarspace Discussion Forums

Home Login Search

cb2000 correct fitting

View related threads: (in this forum | in all forums)

Logged in as: Guest

All Forums >> [Community Discussions] >> Bondage Gear and Apparel >> cb2000 correct fitting

Page: [1]

Message

<< Older Topic Newer Topic >>

cb2000 correct fitting - 7/24/2005 3:50:06 PM

urs2useasuwish

Posts: 1
Joined: 7/4/2005
Status: offline

I have been very fortunate and found a wonderful Mistress/Master to serve. Once of Their requirements is that I wear a CB2000 chastity device however because my testicle are fairly tightly held the rings have a crushing action. Has anyone else experienced this and how did you fix it.

Profile

Post #: 1

RE: cb2000 correct fitting - 7/24/2005 4:06:29 PM

Gemeni

Posts: 255
Joined: 2/19/2005
Status: offline

You look for a custom maker who can fit one properly-instead of trying to get a cheesy off the rack piece of crap to work.

(in reply to urs2useasuwish)

Profile

Post #: 2

RE: cb2000 correct fitting - 7/24/2005 4:43:47 PM

stef

Posts: 10215
Joined: 1/26/2004
Status: offline

quote:

ORIGINAL: urs2useasuwish

I have been very fortunate and found a wonderful Mistress/Master to serve. Once of Their requirements is that I wear a CB2000 chastity device however because my testicle are fairly tightly held the rings have a crushing action. Has anyone else experienced this and how did you fix it.

Gemeni's and ever so helpful advice motwithstanding, the Millers' designs (CB-2000, Curve and CB-3000) can be problematic for someone with a scrotum that doesn't hang all that low. The following note is on their website:

Note: Some men have a high tight ball sack. If this is the case it may take a little longer to get a comfortable exact fit. For the best results the ball sack should hang slightly beneath the cuff ring and cage portion. You may find it necessary to stretch the ball sack. This can be accomplished by ‘The Enhancer’ or by wearing a 1” leather strap off and on around the top of the sack until it stretches slightly. Make sure to smooth the skin under the ball sack to each side. If the skin overlaps, this may cause a burning sensation.

'The Enhancer' (which seems to have been removed from their website ) is just a ball parachute, but it's a tad awkward to wear for anything other than play. A couple of alternatives are weights or a stretching device, which can elongate the scrotum if worn regularly and make wearing the DB device a much more "enjoyable" experience. At least initially

~stef

_____________________________

Welcome to PoliticSpace! If you came here expecting meaningful BDSM discussions, boy are you in the wrong place.

"Hypocrisy has consequences"

(in reply to urs2useasuwish)

Profile

Post #: 3

RE: cb2000 correct fitting - 7/24/2005 4:55:35 PM

PrincessinLatex

Posts: 191
Joined: 7/4/2005
Status: offline

I agree with you. I'm sure one would not encounter such problems with a neosteel or a tollyboy.

(in reply to Gemeni)

Profile

Post #: 4

RE: cb2000 correct fitting - 7/24/2005 5:39:47 PM

stef

Posts: 10215
Joined: 1/26/2004
Status: offline

I hear those Neosteel belts are hard to measure for

~stef

_____________________________

Welcome to PoliticSpace! If you came here expecting meaningful BDSM discussions, boy are you in the wrong place.

"Hypocrisy has consequences"

(in reply to PrincessinLatex)

Profile

Post #: 5

RE: cb2000 correct fitting - 7/24/2005 5:44:57 PM

PrincessinLatex

Posts: 191
Joined: 7/4/2005
Status: offline

I've used a measuring kit for the neosteel. There might be some sizing issues at first (I think it is just because it was the first time shayler and I have had to do such measurements) but they allow you to send it back to be redone with the new measurements. The measurements will eventually be correct. . . .I hope (since there are two engineers involved here.)

(in reply to stef)

Profile

Post #: 6