Suspension Rack (Full Version)

All Forums >> [Community Discussions] >> Bondage Gear and Apparel



Message

orlandoslv -> Suspension Rack (4/5/2009 7:42:20 AM)

my Goddess has a new suspension rack and i am looking for some type of system that would help Her hoist me up, especially upside down.  i have thought about using those ratchet tie downs or the two pulley systems to help Her raise me off the floor.  Anybody have any ideas or suggestions.




Domin8tingUrDrmz -> RE: Suspension Rack (4/5/2009 7:46:19 AM)

A rigger I know uses pulleys as you mentioned.  He also uses a device which locks the rope in place once the pulleys have hoisted the person to the desired height.  I do not know what that locking mechanism is called, but he said without it he had persons slip rather quickly and land poorly even after tying the hoisting rope off.  I believe he uses a 3 pulley system, not a two.



GotSteel -> RE: Suspension Rack (4/5/2009 8:55:27 AM)

There are a number of rope clamps and pulley systems or just plain carabiners and knots used in rock climbing to haul up heavy loads. Researching "big wall hauling" would get you useful information. A clamping mechanism that can also be released under load and used to lower the sub in a controlled manner could be useful to you: http://www.mountaingear.com/pages/product/product.asp/imanf/Trango/idesc/Cinch+Belay+Device/Store/MG/item/114056/N/1027
But make sure to do your research, so that you have a system that you can get out of quickly.



J69B -> RE: Suspension Rack (4/5/2009 12:21:35 PM)

Climbing/rigging hardware is a good bet when doing a suspension.  The hardware is all load rated and pretty simple to use.  I use double sheave blocks to build compound pulley systems for easier lifting of heavier loads.  I also use a special jam cleat to lock the line.  I have also used figure 8 descenders to control decent.  All of this equipment is available at good climbing stores.  What is more important than the equipment however is the skill in setting it up safely.  Be sure you seek qualified help in how to safely use things.  A fall from even a short height can put you in the emergency room and that isn't a good ending to a suspension scene.



GotSteel -> RE: Suspension Rack (4/5/2009 1:01:15 PM)

I couldn't agree with you more.



fielder -> RE: Suspension Rack (4/6/2009 9:48:18 AM)

Sir, Harbor Freight makes several 110 VAC, (elect) winches. Bolted to the floor, wall, and a couple of pulleys. One over the rack and a turning pulley would do the trick quite nicely. The winch comes with a remote control and is power up and down and has an elect brake when turned off.
Fielder, of Maryland



fielder -> RE: Suspension Rack (4/8/2009 7:35:17 AM)

Go to any good marine store. In the sail boat area you will find any number of ropes, block and tackles, pulleys and the fitting for securing the rope from going back through the block and tackle.



frenchdungeon -> RE: Suspension Rack (4/8/2009 8:15:57 AM)

quote:

ORIGINAL: fielder

Sir, Harbor Freight makes several 110 VAC, (elect) winches. Bolted to the floor, wall, and a couple of pulleys. One over the rack and a turning pulley would do the trick quite nicely. The winch comes with a remote control and is power up and down and has an elect brake when turned off.
Fielder, of Maryland


110 vac elec winch, is what i have, i have installed it inside the ceilling rafter, and reinforced the rafters with 2x4, i had a 4 foot steel bar 2" square tube made for this purpose, we use it for suspension only, it comes with a remote, for easy lifting, its a very efficient way for suspension play



Irishm57 -> RE: Suspension Rack (4/8/2009 10:33:16 AM)

At first i was using a boat winch, cost's around 20-30 bucks at walmart. (The winch that goes on a boat trailer to pull the boat in). I mounted that to side of the bonadage frame using 3 inch U bolts. And ran 1/2 inch nylon rope on it through a pully mounted to the top center of the frame. on the other end i had a piece of 3/4 black iron pipe (3 feet long) with eye bolts on the end. This was to attack my ankles to for upside down suspension.
http://www.slavechris.com/upsidedown/upsidedown.html

After a year of that, i upgraded and bought a 120 volt, 880 pound electric winch, on my main page there is a link to my playroom pics which show the electric winch i mounted . Forgot to add the electric winch as on sale at the time at harbor freight for 100 bucks. they usualy float at around that price year round , you just have to catch them when it is on special




Joseff -> RE: Suspension Rack (4/9/2009 8:58:03 PM)

For  a more industrial feel, you might consider a chainfall winch. It is a geared block and tackle type of device most often used by mechanics. Makes a great clanking noise, and doesn't need locking or clamping. They use these to lift car engines, they'll easily lift a sub.
Joseff



azropedntied -> RE: Suspension Rack (4/19/2009 12:28:42 AM)

used medical supply stores ,pool and bath  people lifters .some even come with a sling ,chair and or harness .



Guilty1974 -> RE: Suspension Rack (4/19/2009 10:47:46 AM)

Pulleys, tackles, whiches etc. can be handy for hogtied.com style supsenions, but come with the disadvantage of unpredictable forces on the body. For most if not all Japanese style suspension - including upside-down ones - you don't need any other hardware than a solid hardpoint.



Page: [1]

Valid CSS!




Collarchat.com © 2025
Terms of Service Privacy Policy Spam Policy
0.03125