ball stretching with weights

Collarspace Discussion Forums

Home Login Search

ball stretching with weights

View related threads: (in this forum | in all forums)

Logged in as: Guest

All Forums >> [Community Discussions] >> Bondage Gear and Apparel >> ball stretching with weights

Page: [1]

Message

<< Older Topic Newer Topic >>

ball stretching with weights - 6/20/2006 12:31:04 PM

bimale2serveu

Posts: 5
Joined: 11/26/2005
Status: offline

i currently use some hand weight 2 pounds each on each ball to stretch it and also to cause some pain.. i use rope to tie them onto my balls is there a better method to tie them on with. the rope doesnt get tight and its a pain to untie afterwards.. i am just looking for homemade ideas i know there is stuff that can be purchased... thanks for any help

Profile

Post #: 1

RE: ball stretching with weights - 6/21/2006 3:33:58 PM

switcherCT

Posts: 7
Joined: 11/22/2005
Status: offline

The most common device for this is a parachute. Most go around the scrotum and snap closed, the problem with these is when you get up to around five pounds the snaps become undone and the parachute and weights fall to the floor hopefully not on your toes. If you are going to get a parachute get one that laces closed like a pair of shoes, these will hold alot of weight.

IF YOU WANT TO MAKE YOUR OWN.

You can make a unit from two pieces of wooden dowel about 3/4" diameter be about 8" long. Drill holes near each end of the dowels, make sure they line up on both pieces. Get two 3/16" machine screws about 4" long, two hex nuts, six flat washers, two wing nuts, two 8" pieces of small jack chain, four small S hooks, and one 1 1/2" steel ring.

Place one washer each machine screw and and insert into the holes in one of the dowels. Place one washer and hex nut on each machine screw and tighten the nut all the way up to the dowel. Slide the the other dowel onto the machine screws. Place one flat washer and one wing nut on each machine screw. This will alow you to adjust the space between the two dowels by turning the wing nuts.

Attach an S hook to each end of the chain and squeze shut with pliers. Attach one end of each chain to the steel ring with S hooik and close with pliers. Attach other end of each chain to each machine screw between the two dowels. The steel ring is where you attach the weights.

RECOMENDATION
The above is a fair amount of work and the materials will cost almost as much as the next item.

I have found the best item to use is also the cheapest. I have lifted twenty pounds with one of these and there is no problem with pinching or it sliding off. Of course 20 pounds is going to hurt but it is the good hurt that you are looking for. It is also easy to apply and take off.

The item is called a Screw Twitch Aluminum. It is made for holding a horses mouth open and is sold at Vet supply or tack shops. It can also be found at BDSM stores that cater to gay men but at a much higher price.

4showhorsetack.com lists the item for $10.95

To use the item you open it up and insert the balls between the two jaws and then turn the scres to bring the two jaws together behind the balls, clamping down on the scrotum. You can screw it doiwn very tight without it hurting and then hang your weights to the eye in the screw handle.

SwitcherCT

(in reply to bimale2serveu)

Profile

Post #: 2

RE: ball stretching with weights - 6/27/2006 11:57:34 PM

marshastoy

Posts: 5
Joined: 6/27/2006
Status: offline

Mistress has a padlock which she puts my balls through and snaps shut. There is just enough room to squeeze my sack between the U part. I wear this instead of a collar in public. It grips my balls really well. Sometimes she hangs a chain off it with a 2.5Kgs wightlifting weight on.

Marshas toy

(in reply to switcherCT)

Profile

Post #: 3