Titty Puller

Collarspace Discussion Forums

Home Login Search

Titty Puller

View related threads: (in this forum | in all forums)

Logged in as: Guest

All Forums >> [Community Discussions] >> Bondage Gear and Apparel >> Titty Puller

Page: [1]

Message

<< Older Topic Newer Topic >>

Titty Puller - 10/5/2009 2:25:22 PM

summittome

Posts: 1
Joined: 8/28/2009
Status: offline

The favorite of all my toys and it costs almost nothing to build. I will try my best to describe it.

Get a large paint stirrer, not the regular size but the next size up. Drill holes to insert a toothpick in about 1/2 in apart along the length of a 3/8 in dowel, 12 in long. Glue the dowel (use carpenters glue) flush with the stirrer.

Drill a hole in the middle of a piece of balsa wood about 4X4 in for the dowel to slide through. Drill another in the balsa for a second dowel 12 in long running perpendicular to the first.

At each end of the second dowel attach a small eye hook. Now attach your Japanese Clover Clamps to the eye hooks.

Place the stirrer against her chest between her tits, attach the clamps to her nipples, pull out on the balsa till you get a good stretch (I mean a good stretch..haha) and insert a toothpick to keep the balsa from slipping back.

Profile

Post #: 1

RE: Titty Puller - 10/5/2009 6:53:19 PM

BalletBob

Posts: 1645
Joined: 7/14/2005
Status: offline

Do you have any Pictures of this? I made Nipple Suction Tubes from some Glue Syringes, and they work great too. Very YUMMY for me.

Puppies in love for torment, sub BalletBob

_____________________________

"I get my kicks above the Waistline, Sunshine"

(in reply to summittome)

Profile

Post #: 2

RE: Titty Puller - 10/16/2009 7:29:00 PM

markel

Posts: 17
Joined: 8/10/2005
Status: offline

This may be of some interest:
http://tinyurl.com/ygyjq63

< Message edited by markel -- 10/16/2009 7:33:14 PM >

(in reply to BalletBob)

Profile

Post #: 3

RE: Titty Puller - 10/28/2009 8:18:49 AM

lisub4one

Posts: 94
Joined: 6/9/2006
Status: offline

i've made similar devices from material readily available from the local Dom Depot/Lowe's/ACE Hardware for about $10:

8" - 1"x3" lumber
12" - 3/4" square dowel (round are just harder to drill a true hole through, but can be used)
12" - 1/4"x20 threaded rod
1/4"x20 'T' nut or threaded insert (look in the slide out plastic hardware drawers in any of the stores)
1/4"x20 nut with free spinning washer attached (look in the slide out plastic hardware drawers in any of the stores)
1/4"x20 control knob (look in the slide out plastic hardware drawers in any of the stores)
2 - 1/4"x20 nuts
2 - clothespins
bungee cord - two pieces 8" - 12" long
PL-2000 or similar construction adhesive

drill a shallow hole, not a through hole, in the center of the 1x3 wide enough to accept the washer of the free spinning washer nut.
glue the free spinning washer nut into the hole in the 1x3 with PL-2000, making sure not to get any adhesive on the nut so that it remains free spinning. Clamp in place and allow to set overnight.
thread a nut onto the 1/4x20 rod about 1/2", then thread the rod into the free spinning nut and tighten the two nuts against each other with wrenches so that as the rod turns the two nuts turn together.
drill a centered hole at the middle of the length of the 3/4" dowel to accept the 'T' nut/threaded insert and install.
drill a centered hole 1" from each end of the 3/4" dowel just large enough to accept the bungee cord doubled over.
thread the 3/4" dowel half way down on to the 1/4"x20 rod.
thread the second nut onto the end of the 1/4"x20 rod about 1/2", then thread on the 1/4"X20 control knob and tighten the nut against the bottom of the knob with wrenches so that the rod and knob turn together as a unit.
thread a bungee cord through the spring of a clothespin and pass the two ends through a hole at the end of the 3/4" dowel, tying a knot so that the bungee cord cannot pull back through the hole. Repeat with the second clothespin.

Place the 1x3 base against the center of the chest, attache a clothespin to each nipple, and then turn the control knob clockwise to tighten and stretch. Once you have started to stretch the nipples a small turn is all it takes to renew the "sensation". The device works equally well on male and female subjects.

If i can borrow one back from one of the Dommes i've made one for i will post a pic.

(in reply to markel)

Profile

Post #: 4

RE: Titty Puller - 10/29/2009 7:27:47 PM

BalletBob

Posts: 1645
Joined: 7/14/2005
Status: offline

Markel, Thanks so much. It is really kewl. I tried to make one a long time ago like this, but gave up on it. It looks so NICE ! My Puppies would love something like this too. LOL

Nipples waiting, sub BalletBob

_____________________________

"I get my kicks above the Waistline, Sunshine"

(in reply to markel)

Profile

Post #: 5